Does a lower compression engine require more crank spark?
How does crank spark effect crank load?
Cranking
-
m-barans
- Posts: 88
- Joined: 2021 Feb 16, 23:09
- Location: Lafayette, Oregon US
- Vehicle Information: 2003 Mercury Marauder 300A with new stock bore IRON 4.6 block, Manley crank, Manley H-tuff h-beam rods, CP pistons with stainless rings, ARP head studs, GT500 lash adjusters and rollers, D series cylinder heads, VMP GEN3R 2.65 L TVS blower, 80 lb/hr FRPP Siemens Deka injectors, HPX slot 100mm MAF, coyote mustang fuel pump with Holley 60 psi filter/regulator return at pump, Stainless works long tube headers and complete exhaust, Moates quarter horse and TunerPro RT with support from Decipha, RZASA strategy.
2001 Ford Lightning SVT F-150 stock engine w/ inlet ported M112, GT500 rollers, ARP head studs, metco quick change upper pulley with stock sized upper, K&N intake system, bassani SS exhaust system from the stock manifold flanges back. 4x4 trans oil pan. SSBC big brakes 14” up front. Work/Street truck. My “next to build” with trick flow heads (before extinction) with h-beams & cobra jet crank (sitting in tool box) and proper pistons. Next up after the marauder is dialed in.
-
decipha
- Posts: 5098
- Joined: 2021 Feb 15, 12:23
- Location: Metairie, LA
- Vehicle Information: Work Truck
'19 F-150 3.3L
Re: Cranking
No
It doesnt.
It doesnt.
-
m-barans
- Posts: 88
- Joined: 2021 Feb 16, 23:09
- Location: Lafayette, Oregon US
- Vehicle Information: 2003 Mercury Marauder 300A with new stock bore IRON 4.6 block, Manley crank, Manley H-tuff h-beam rods, CP pistons with stainless rings, ARP head studs, GT500 lash adjusters and rollers, D series cylinder heads, VMP GEN3R 2.65 L TVS blower, 80 lb/hr FRPP Siemens Deka injectors, HPX slot 100mm MAF, coyote mustang fuel pump with Holley 60 psi filter/regulator return at pump, Stainless works long tube headers and complete exhaust, Moates quarter horse and TunerPro RT with support from Decipha, RZASA strategy.
2001 Ford Lightning SVT F-150 stock engine w/ inlet ported M112, GT500 rollers, ARP head studs, metco quick change upper pulley with stock sized upper, K&N intake system, bassani SS exhaust system from the stock manifold flanges back. 4x4 trans oil pan. SSBC big brakes 14” up front. Work/Street truck. My “next to build” with trick flow heads (before extinction) with h-beams & cobra jet crank (sitting in tool box) and proper pistons. Next up after the marauder is dialed in.
Re: Cranking
If cranking spark is null then that leads me to believe that more throttle body bypass mass air may be needed along with some additional enrichment. I will try that out
-
m-barans
- Posts: 88
- Joined: 2021 Feb 16, 23:09
- Location: Lafayette, Oregon US
- Vehicle Information: 2003 Mercury Marauder 300A with new stock bore IRON 4.6 block, Manley crank, Manley H-tuff h-beam rods, CP pistons with stainless rings, ARP head studs, GT500 lash adjusters and rollers, D series cylinder heads, VMP GEN3R 2.65 L TVS blower, 80 lb/hr FRPP Siemens Deka injectors, HPX slot 100mm MAF, coyote mustang fuel pump with Holley 60 psi filter/regulator return at pump, Stainless works long tube headers and complete exhaust, Moates quarter horse and TunerPro RT with support from Decipha, RZASA strategy.
2001 Ford Lightning SVT F-150 stock engine w/ inlet ported M112, GT500 rollers, ARP head studs, metco quick change upper pulley with stock sized upper, K&N intake system, bassani SS exhaust system from the stock manifold flanges back. 4x4 trans oil pan. SSBC big brakes 14” up front. Work/Street truck. My “next to build” with trick flow heads (before extinction) with h-beams & cobra jet crank (sitting in tool box) and proper pistons. Next up after the marauder is dialed in.
Re: Cranking
Update: Adding additional crank PW (Load) has helped. I opened the throttle bypass more during cranking and In addition: I reduced returnless pump prime time to almost nothing. I am getting better “torch-offs” now