EEC V file conversion

All hardware related, disassembly / programming and code discussions belong here.
mechanicalmatch
Posts: 88
Joined: 2021 Apr 15, 10:56
Location: Spring Texas
Vehicle Information: 00 F150 4.6L Extended cab
CVAF1
4R70 3.08

EEC V file conversion

Unread post by mechanicalmatch »

post your file here with information of what you used read (pcm flash, qh , etc...) with and what you want it to be converted to be used on (pcm flash, qh , etc...)and i will convert it for you.
decipha
Posts: 4955
Joined: 2021 Feb 15, 12:23
Location: Metairie, LA
Vehicle Information: Work Truck
'19 F-150 3.3L

Re: EEC V file conversion

Unread post by decipha »

thats very kind of you

I have a cheat sheet in the disassembly write up with step by step details for doing so as well.
mechanicalmatch
Posts: 88
Joined: 2021 Apr 15, 10:56
Location: Spring Texas
Vehicle Information: 00 F150 4.6L Extended cab
CVAF1
4R70 3.08

Re: EEC V file conversion

Unread post by mechanicalmatch »

yes sir. i learned a lot from your write up.
BOOSTEDEVERYTHING
Posts: 218
Joined: 2023 Sep 06, 13:11
Location: Charlotte NC , USA
Vehicle Information: 1999 Ford Ranger with 2000 Explorer v8 swap, FLN0
2003 Ford F150 Harley Davidson, Built 5.4L SOHC with 3.4L Whipple and Built 4R100

Re: EEC V file conversion

Unread post by BOOSTEDEVERYTHING »

I have a bin that i pulled off of an FLN0 pcm that I would like to run through SAD and attempt to build an XDF file for so I can understand more about how everything works. could you help me with that? I used a burn 1 and adapters and flash and burn software to pull it from the pcm. If not I understand. I am a little confused about where the filler lines are and how to actually read code. I tried to edit the REAC4 XDF in Tunerpro but it is password protected. probably for good reason. Thanks
Attachments
eqe3_ml2_8a1a_stock read burn1fnb.bin
Used flash and burn to pull with burn 1+f2a+f2e
(256 KiB) Downloaded 389 times
decipha
Posts: 4955
Joined: 2021 Feb 15, 12:23
Location: Metairie, LA
Vehicle Information: Work Truck
'19 F-150 3.3L

Re: EEC V file conversion

Unread post by decipha »

What you asking is a huge undertaking.

Read the disassembly write up on the homepage everything you need to know is there.

It takes several years to disassemble a strategy.
BOOSTEDEVERYTHING
Posts: 218
Joined: 2023 Sep 06, 13:11
Location: Charlotte NC , USA
Vehicle Information: 1999 Ford Ranger with 2000 Explorer v8 swap, FLN0
2003 Ford F150 Harley Davidson, Built 5.4L SOHC with 3.4L Whipple and Built 4R100

Re: EEC V file conversion

Unread post by BOOSTEDEVERYTHING »

I’m not asking for it to be disassembled. Just for it to be put into the order that it should be put in to start disassembly. I just don’t quite understand how to tell what exactly is filler and how to tell the start and end of the banks. The examples given don’t look like what I’m seeing in the binary editor I’m using. Maybe I should be using a different editor? Also, do I build the xdf file directly in tunerpro, or is there a different software for that?
jsa
Posts: 260
Joined: 2021 Feb 16, 15:46
Location: Australia
Vehicle Information: 95 Escort RS Cosworth
2.0 YBP
CARD / QUIK / COSY / ANTI
GHAJ0
SMD-190 / SMD-490 EEC-IV

Binary Editor
ForDiag

Re: EEC V file conversion

Unread post by jsa »

BOOSTEDEVERYTHING wrote: 2023 Sep 23, 15:12 I’m not asking for it to be disassembled. Just for it to be put into the order that it should be put in to start disassembly.
It disassembles as is with SAD 4.12
https://github.com/tvrfan/EEC-IV-disass ... _4.012.exe
Attachments
eqe3--SAD412.zip
(554.68 KiB) Downloaded 381 times
BOOSTEDEVERYTHING
Posts: 218
Joined: 2023 Sep 06, 13:11
Location: Charlotte NC , USA
Vehicle Information: 1999 Ford Ranger with 2000 Explorer v8 swap, FLN0
2003 Ford F150 Harley Davidson, Built 5.4L SOHC with 3.4L Whipple and Built 4R100

Re: EEC V file conversion

Unread post by BOOSTEDEVERYTHING »

Awesome! Thank you so much. I was following the write up and was really confused about where to go with that. So with v4.12 the order is 0189, with file size 256k for all 4 bank bins then?
jsa
Posts: 260
Joined: 2021 Feb 16, 15:46
Location: Australia
Vehicle Information: 95 Escort RS Cosworth
2.0 YBP
CARD / QUIK / COSY / ANTI
GHAJ0
SMD-190 / SMD-490 EEC-IV

Binary Editor
ForDiag

Re: EEC V file conversion

Unread post by jsa »

SAD will disassemble other 4 bank orders and sizes.
BOOSTEDEVERYTHING
Posts: 218
Joined: 2023 Sep 06, 13:11
Location: Charlotte NC , USA
Vehicle Information: 1999 Ford Ranger with 2000 Explorer v8 swap, FLN0
2003 Ford F150 Harley Davidson, Built 5.4L SOHC with 3.4L Whipple and Built 4R100

Re: EEC V file conversion

Unread post by BOOSTEDEVERYTHING »

Would you happen to have an open source xdf file that I can look at in the editor so I can get a good idea of what I’m trying to do to build one for my pcm? I’m not looking for a hand out but I’m more of a visual learner and to see an example one would help tremendously. I’m not sure when I’m disassembling when I’m putting data into the Directive file, what I’m actually supposed to be putting in there and why, also not sure if that is building the xdf file or if I then have to manually enter in all the data from the directive file into the xdf editor in tunerpro. Sorry for all the questions. I’d really like to learn this stuff and honestly think it would help in my daily job to understand this better as well. I have been tuning various vehicles for years. I get that part of it. It’s the behind the scenes things. Thanks.
Post Reply