And then the 60lbs siemens patch since I'm running the black Siemens 60's?
Code: Select all
4.950000197 1146.135274
4.800000191 1069.578063
4.650000185 992.9662965
4.500000179 917.2188745
4.350000173 843.1169724
4.200000167 771.3123465
4.050000161 702.3378612
3.900000155 636.6155165
3.750000149 574.4656289
3.600000143 516.1151564
3.450000137 461.7068738
3.300000131 411.3074984
3.150000125 364.9157961
3.000000119 322.4713125
2.850000113 283.8618365
2.700000107 248.9318103
2.550000101 217.4898909
2.400000095 189.3164845
2.250000089 164.1715715
2.100000083 141.8019293
1.950000077 121.948309
1.800000072 104.3527913
1.650000066 88.76559583
1.50000006 74.95202017
1.350000054 62.69919973
1.200000048 51.82264377
1.050000042 42.17275037
0.900000036 33.64112931
0.75000003 26.16681821
0.600000024 19.7423474
I will thanks!
I put the injector data in (using your Siemens 60 patch), then the 24lb calibrated MAF, SARCHG,decipha wrote: ↑2022 May 18, 06:57 No, u havw to put the injector data in first then the maf
read the comments on the injector high slope
they are all the same just displayed to you differently
i wouldnt recommend using the maf he poated as it doesnt go to max and min volts and the points are outside of the histogram so youd have to manually dial it in
Yes. I might redownload the A9L2 and start back over to make sure.
Code: Select all
05/16/2022 16:12:19 Scalar: SP** (WARNING) AHISL - Injector High Slope **SEE COMMENTS** changed from 19.641 lbs/hr (0x13A4) to 60.270 lbs/hr (0x3C45).
05/16/2022 16:13:35 Scalar: SP** ALOSL - Injector Low Slope [lbs/hr] changed from 80.087 lb/hr (0x5AB6) to 63.191 lb/hr (0x4793).
05/17/2022 08:28:01 Patch: INJECTORS - 60LB @ 40PSI - LU60 Siemens Deka 60s changed.
05/17/2022 08:35:57 Function: Crank PW ECT Modifier - FN348 changed.
05/17/2022 08:43:38 Scalar: SP**_SARCHG - Engine Size Displacement changed from 926.66 Cubic In. (0x29CF) to 301.99 Cubic In. (0x0DA0).
05/17/2022 16:36:36 Function: SP** MAF Transfer - AM - FN036 (approximate) changed.
05/17/2022 22:28:59 Function: SP** MAF Transfer (volts) - kg/hr - FN036 changed.
05/17/2022 22:42:14 Patch: KAM Clear At Key On - Z_KAMCLR (Adapt Disable / FADPT_SW) (Disables Idle Spark Corr ?) changed.
05/17/2022 22:59:45 Function: Injector Offset Lag Time - FN367 (Crank PW Modifier) changed.
05/18/2022 07:32:32 Function: SP** MAF Transfer - AM - FN036 (approximate) changed.
Yeah pump shuts off after 3s of priming, how do I verify it's communicating well with the ECU?