400hp 351w startup tune
-
- Posts: 137
- Joined: 2021 Nov 08, 22:24
- Location: North Central IL
- Vehicle Information: 1995 F-250 RCLB with a built 300 and 4-spd running A1C
wbo2_aem_uego
Re: 400hp 351w startup tune
The regulator for the same year truck with a 4.9L straight six will have a ~55 psi regulator. Ford upped the fuel pressure on the straight sixes to combat vapor lock in the fuel rail due to it sitting directly above the exhaust manifolds.
-
- Posts: 399
- Joined: 2021 Feb 15, 22:12
- Location: Sacramento CA
- Vehicle Information: 1991 F150 4.9L J1X 80lb Injectors E85
1995 F150 5.8L MOB1
Re: 400hp 351w startup tune
Yeah, I found an old one from my 4.9 but it would have to be modified to mount up correctly. I'll just run the stock regulator for now.
-
- Posts: 399
- Joined: 2021 Feb 15, 22:12
- Location: Sacramento CA
- Vehicle Information: 1991 F150 4.9L J1X 80lb Injectors E85
1995 F150 5.8L MOB1
Re: 400hp 351w startup tune
Failed emissions at idle today. Allowed is 100PPM of HC and she read 239PPM. It is a bit rumpety at idle, so it has to be the cam profile causing it. At 2500RPM, 180PPM allowed and it read 15.
Idle speed is under 700rpm so thinking I need to kick it up a bit to pass. Timing jumps around 15-25 degrees at idle. Any other help? Some have mentioned leaning it out a bit but not sure how to force OL at idle.
Idle speed is under 700rpm so thinking I need to kick it up a bit to pass. Timing jumps around 15-25 degrees at idle. Any other help? Some have mentioned leaning it out a bit but not sure how to force OL at idle.
-
- Posts: 183
- Joined: 2021 Mar 22, 15:58
- Location: Newington CT
- Vehicle Information: 1986 Mustang GT, Stock block, TFS 170 Heads , N41 cam, ported cobra intake, nitrous, T5 , 3.73s
Re: 400hp 351w startup tune
2500 rpm 15ppm is good, so the cats may not be hot enough at idle. Also locking the timing at 10 is helpful. I would try a higher idle speed like you said (850-900ish) but they may have a max idle speed requirement...
-
- Posts: 399
- Joined: 2021 Feb 15, 22:12
- Location: Sacramento CA
- Vehicle Information: 1991 F150 4.9L J1X 80lb Injectors E85
1995 F150 5.8L MOB1
Re: 400hp 351w startup tune
Awesome, I set the idle to 850 and timing at 13*. at 10 it hunts a bit more I think because the minimum idle timing is 10. Should I lower the minimum or leave at 13?
I'll be having it tested again in the morning. I noted that the engine needs a bit more air and fuel at idle now. Is the flame burning into the exhaust port increasing temps?
I'll be having it tested again in the morning. I noted that the engine needs a bit more air and fuel at idle now. Is the flame burning into the exhaust port increasing temps?
-
- Posts: 183
- Joined: 2021 Mar 22, 15:58
- Location: Newington CT
- Vehicle Information: 1986 Mustang GT, Stock block, TFS 170 Heads , N41 cam, ported cobra intake, nitrous, T5 , 3.73s
Re: 400hp 351w startup tune
Yes, the later burn sends more heat out the exhaust which gets the cats up to temp. 13 will prob still work.
-
- Posts: 6384
- Joined: 2021 Feb 15, 12:23
- Location: Metairie, LA
- Vehicle Information: Work Truck
'25 F-150 5L
Re: 400hp 351w startup tune
lower the timing to reduce emissions, idling at 6 degrees is fine you just need to kick up the idle air thus the throttle stop would need some love to get the idle stable again
the lower the idle spark the more torque reserve you have
you can also allow more egr at idle too in order to re-burn some of that fuel in the exhaust if you can
the lower the idle spark the more torque reserve you have
you can also allow more egr at idle too in order to re-burn some of that fuel in the exhaust if you can
-
- Posts: 399
- Joined: 2021 Feb 15, 22:12
- Location: Sacramento CA
- Vehicle Information: 1991 F150 4.9L J1X 80lb Injectors E85
1995 F150 5.8L MOB1
Re: 400hp 351w startup tune
Thanks, it passed just fine. Was still a bit rich at idle so guy let me set the hego bias to full lean and it cleaned right up.