'07 Town Car V10 Swap?

For all other non specifically listed ECU tuning. This would include can-bus ecu's such as powerpc copperhead tricore and siemens ecus. As well as GM, Dodge or any aftermarket controller tuning etc...
Sevensecondsuv
Posts: 111
Joined: 2021 Nov 08, 22:24
Location: North Central IL
Vehicle Information: 1994 F-350 CCLB 7.5/ZF/4wd
1995 F-250 RCLB 4.9/T18/4wd
2000 Excursion 6.8/4R100/4wd
2001 Ranger RCSB 2.3/M5OD/2wd - turbocharged
2007 Town Car 4.6/4R75E
2011 Ranger SCSB 2.3/M5OD/2wd
wbo2_aem_uego

'07 Town Car V10 Swap?

Unread post by Sevensecondsuv »

I have an '07 Town Car that just got retired from daily driving service. I also have a line on a 2v V10 out of an excursion for cheap. I've always wanted to V10 swap one of these cars. I realize there's far better options to make horsepower, but this would be more about the feeling of slinging the big heavy Lincoln around effortlessly with minimal throttle inputs. Having driven trucks and Excursions with the V10, I think it would excel in this role.

Obviously bolting it in place of the 4.6 would be a fairly straightforward affair, save for some clearance issues with the brake booster, HVAC box, and throttle elbow. Those are all solvable, however. What I'm not sure of is the computer. What I do know about the '05+ stuff is that the ECU is more or less married to every other component in the car via can-bus. So I don't think swapping the ECU for one out of a truck would work.

Is it possible to add outputs for 2 more injectors, coils, and change firing order, etc via a tune to the stock ECU? Or would I be looking at a real science project swapping hardware?
decipha
Posts: 4950
Joined: 2021 Feb 15, 12:23
Location: Metairie, LA
Vehicle Information: Work Truck
'19 F-150 3.3L

Re: '07 Town Car V10 Swap?

Unread post by decipha »

no just swap the ecu from a truck its all the same
Sevensecondsuv
Posts: 111
Joined: 2021 Nov 08, 22:24
Location: North Central IL
Vehicle Information: 1994 F-350 CCLB 7.5/ZF/4wd
1995 F-250 RCLB 4.9/T18/4wd
2000 Excursion 6.8/4R100/4wd
2001 Ranger RCSB 2.3/M5OD/2wd - turbocharged
2007 Town Car 4.6/4R75E
2011 Ranger SCSB 2.3/M5OD/2wd
wbo2_aem_uego

Re: '07 Town Car V10 Swap?

Unread post by Sevensecondsuv »

OK.....The can-bus trucks were running 3v V10s by then, so I guess that's what I'm looking for as a donor. Those aren't cheap yet like the 2v donors.....

That's interesting that you can just swap ECUs. That's the opposite of everything else I've read about the '05+ can-bus Fords. I've seen a few threads where people tried and ended up having to swap in the cluster, fuel pump driver, trans, rear axle, entire harness, radio, etc just to get it to start. I'm assuming you'd have to flash the truck's computer with the town car VIN and whatnot and that's what would allow it to work in the town car chassis?

Using the 3v truck ECU would probably also force me to use a 5R110 trans vs the 4R75E that's in the car. I guess that'd be a pretty nice upgrade - if it fit inside the trans tunnel anyways.

What about the earlier cars? I'm guessing an 03/04 Town Car ECU isn't going to run a V10 either. Will a V10 truck ECU run a 4R70?
decipha
Posts: 4950
Joined: 2021 Feb 15, 12:23
Location: Metairie, LA
Vehicle Information: Work Truck
'19 F-150 3.3L

Re: '07 Town Car V10 Swap?

Unread post by decipha »

No people are ignorant they dont understand its just a calculator it does only what you tell it. You never have to swap wiring or hardware or any of that crap. Thats probably the same idiots that recommend replacing entire harnesses for cobra and lightning engine swaps. Dont believe any of that crap you hear.

5r is a downgrade to the 4r

yeah an earlier v10 truck ecu can do both but it would require the tasc strategy be broken out significantly.
pcwizzy37
Posts: 5
Joined: 2023 Jun 10, 02:10
Location: Glendale, Oregon, USA
Vehicle Information: 1991 Ford F-250HD XLT Lariat 7.5L V8 EFI, E4OD, EEC-IV SD36E S0J
1991 Ford F-250 XL 4.9L i6 EFI, ZF-5, EEC-IV SD40A E1M
1995 Ford F-250HD XLT, 7.5L V8 EFI, EEC-IV SD48A DOE0, manual swapped

Re: '07 Town Car V10 Swap?

Unread post by pcwizzy37 »

Use a 2005-2008 V10 2v PCM from a van, older and it's EEC-V, newer and it uses a different CAN bus protocol.
decipha
Posts: 4950
Joined: 2021 Feb 15, 12:23
Location: Metairie, LA
Vehicle Information: Work Truck
'19 F-150 3.3L

Re: '07 Town Car V10 Swap?

Unread post by decipha »

what trans did those use ?
BOOSTEDEVERYTHING
Posts: 215
Joined: 2023 Sep 06, 13:11
Location: Charlotte NC , USA
Vehicle Information: 1999 Ford Ranger with 2000 Explorer v8 swap, FLN0
2003 Ford F150 Harley Davidson, Built 5.4L SOHC with 3.4L Whipple and Built 4R100

Re: '07 Town Car V10 Swap?

Unread post by BOOSTEDEVERYTHING »

Those vans used the Torqshift Trans.
Post Reply