Search found 28 matches

Return to advanced search

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Ok update: I retorqued all head bolts. Ran the Leak down and coolant pressure test. All good no bubbles in coolant. Super flushed the entire system so it's straight water. Ran a coolant gas check. FAILED. Gasses are getting into the coolant track. I'm going to remove the headd and see if the gasket ...
by beyondEOD
Fri Jul 03, 2020 4:19 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Very good, I was thinking coil would be soon if the TFI did not change anything.

Looking at coils.
Motorcraft vs Delphi?? Delphi is half the cost, does it work half as good?
by beyondEOD
Sat Jun 27, 2020 9:02 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Alright today was productive. Pulled valvecovers and upper intake. Checked tq on head bolts and readjusted valvetrain. Lower intake was pretty loose. I took them to 25ftlbs. Performed leakdown on each cylinder. All good. No bubbles in coolant. Regapped plugs back out to .054 since .040 made no diffe...
by beyondEOD
Sat Jun 27, 2020 8:37 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

That is true, I didnt think of that
by beyondEOD
Fri Jun 26, 2020 1:56 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Should I have a different TFI. This one appears to be for a Ranger when I search it.
by beyondEOD
Fri Jun 26, 2020 1:42 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Completed coolant system pressure test at 15psi. System holds pressure. Pulled plugs cranked with coolant Pressurized, no signs of coolant coming out the plug holes.
by beyondEOD
Fri Jun 26, 2020 1:15 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

It's a black TFI f1sf-12a297-c1a
by beyondEOD
Fri Jun 26, 2020 12:37 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

I was reading through your reference articles again this morning looking at spark plug recommendations. I stumbled upon where you reference the TFI module as it should be a Gray module for 94 and 95 vehicles. I will check later today but I am almost positive mine has a black module. Outside of whate...
by beyondEOD
Fri Jun 26, 2020 7:22 am
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

It does suck the coolant down. I'm going to do a leak down just in case. I would not think I'd have issues as the heads were machined and I used all the right things.
by beyondEOD
Fri Jun 26, 2020 4:55 am
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Yes sir. I swapped the rotor from the reman since it looked better than the oe. Went out for a drive was able to get it to 5700 on one occasion while logging. Then I realized the car was running 230 degrees after and drove it home. It cooled off to 200 by the time I got back in the driveway. I figur...
by beyondEOD
Thu Jun 25, 2020 7:59 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

I do not see a suitable way to attach a ground wire directly to the distributor. What do you recommend?
by beyondEOD
Thu Jun 25, 2020 1:44 pm
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: 95 Mustang MS3 wont rev past 5xxx rpm

Thanks for the quick reply. I'll try that
by beyondEOD
Thu Jun 25, 2020 11:00 am
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

95 Mustang MS3 wont rev past 5xxx rpm

Hello, Can anyone offer any assistance with my setup. 1995 Mustang GT 5.0 GT40p Heads with 136/360# Springs Anderson B31 Cam Setup: MS3 Gold Box Microsquirt TCU on an AODE I cannot get the car to rev past 5xxx rpm under load or free rev. Pulled autolite 104 plugs and gapped to .042. Checked timing w...
by beyondEOD
Thu Jun 25, 2020 10:48 am
 
Forum: MegaSquirt
Topic: 95 Mustang MS3 wont rev past 5xxx rpm
Replies: 19
Views: 874

Re: AODE EEC-V 94/95 SN95 Wiring Question

Awesome thank you
by beyondEOD
Thu Apr 16, 2020 2:23 pm
 
Forum: Transmission Tuning
Topic: AODE EEC-V 94/95 SN95 Wiring Question
Replies: 4
Views: 291

Re: AODE EEC-V 94/95 SN95 Wiring Question

Where do all those signal returns physically tie together in the harness?

Do they all com in on eec pin 46?
by beyondEOD
Thu Apr 16, 2020 1:50 pm
 
Forum: Transmission Tuning
Topic: AODE EEC-V 94/95 SN95 Wiring Question
Replies: 4
Views: 291

AODE EEC-V 94/95 SN95 Wiring Question

Great write up on your transmission swap page: http://www.efidynotuning.com/4r70w.htm I am trying to get a Microsquirt to control my 95 Mustang AODE through the factory harness. I have a few questions that I hope you would be familiar with. I cannot determine the ground paths from the transmission. ...
by beyondEOD
Thu Apr 16, 2020 8:55 am
 
Forum: Transmission Tuning
Topic: AODE EEC-V 94/95 SN95 Wiring Question
Replies: 4
Views: 291

Re: CBAZA Nitrous Tuning

Anyone have any further advice for what I'm trying to do?

Decipha how would you setup your car?
by beyondEOD
Sat Feb 15, 2020 5:28 pm
 
Forum: EEC-V & SN95 Tuning
Topic: CBAZA Nitrous Tuning
Replies: 4
Views: 329

Re: SOLD BE Dongle

SOLD
by beyondEOD
Sun Feb 09, 2020 9:28 pm
 
Forum: For Sale / Wanted
Topic: SOLD BE Dongle
Replies: 4
Views: 716

Re: BE Dongle

I do not know the age I tested it today with BE 5.189 and it recognizes the dongle. EEC Analyzer does not recognize the dongle as having a license on it.
by beyondEOD
Sun Feb 09, 2020 6:22 am
 
Forum: For Sale / Wanted
Topic: SOLD BE Dongle
Replies: 4
Views: 716

Re: CBAZA Nitrous Tuning

I like the idea of the f3 chip handling the 2nd tune that has brought up a few more questions. Adjust regulator base FP @ 65psi all the time? and scale the slopes by 0.75 or so? Concept in my head fueling control QH and 65 base psi: 1. Arm n2o switch>>relay closes/grounds the F3 changing the tune fo...
by beyondEOD
Sat Feb 08, 2020 1:17 pm
 
Forum: EEC-V & SN95 Tuning
Topic: CBAZA Nitrous Tuning
Replies: 4
Views: 329

Re: BE Dongle

I will get you that later today when I'm back at my garage. I'm also interested in trading for a Jaybird and F3.
by beyondEOD
Sat Feb 08, 2020 11:03 am
 
Forum: For Sale / Wanted
Topic: SOLD BE Dongle
Replies: 4
Views: 716

SOLD BE Dongle

I have a BE dongle for sale. Verified works with BE 5.189 on 2/9/2020.

SOLD


Looking for F3 and Jaybird.
by beyondEOD
Sat Feb 08, 2020 10:46 am
 
Forum: For Sale / Wanted
Topic: SOLD BE Dongle
Replies: 4
Views: 716

CBAZA Nitrous Tuning

Hello decipha, I am still working out what my options are. Car is still currently being put back together. I will be tuning my 95 Auto CBAZA car with your base tune once its up and running. My setup for reference: AODE/4.10 gear gt40p heads Explorer Intake w/65mm BBK TB AFM B-31 Cam 30# bb302 Red in...
by beyondEOD
Sat Feb 08, 2020 6:57 am
 
Forum: EEC-V & SN95 Tuning
Topic: CBAZA Nitrous Tuning
Replies: 4
Views: 329

Re: SOFT TOUCH REV CONTROL possible???

Your right I never want to hit a limiter on spray. My window switch will be set 300 before the hard motor limit. Rethinking what I was asking for and after your reply. I don't need what I was asking for...lol. I was thinking way to hard on this in the wrong direction.

Thank you for the help.
by beyondEOD
Wed Feb 05, 2020 6:12 pm
 
Forum: EEC-V & SN95 Tuning
Topic: SOFT TOUCH REV CONTROL possible???
Replies: 6
Views: 416

Re: SOFT TOUCH REV CONTROL possible???

Alright I looked at it in the patch couple of questions.

1. Is it still a fuel cut?

2. If its ignition cut can it be used as the primary rev limit with the fuel set 4-500 rpm higher.

I setting up a dry kit and don't want to hit a fuel cut limiter on accident. I'll also have a window switch.
by beyondEOD
Wed Feb 05, 2020 7:30 am
 
Forum: EEC-V & SN95 Tuning
Topic: SOFT TOUCH REV CONTROL possible???
Replies: 6
Views: 416

Re: SOFT TOUCH REV CONTROL possible???

Alright do you have a write up on it that you can direct me to?
by beyondEOD
Sat Feb 01, 2020 9:16 pm
 
Forum: EEC-V & SN95 Tuning
Topic: SOFT TOUCH REV CONTROL possible???
Replies: 6
Views: 416

SOFT TOUCH REV CONTROL possible???

Within the CBAZA cal is there any way to setup a spark cut rpm limiter rather than a fuel cut? I'm looking at getting an MSD 8728 to do this unless tunerpro can take care of this function. Also would want to replicate a soft touch(select cyl ignition cut) to reduce backfire chances.
by beyondEOD
Fri Jan 31, 2020 10:00 pm
 
Forum: EEC-V & SN95 Tuning
Topic: SOFT TOUCH REV CONTROL possible???
Replies: 6
Views: 416

Re: Recommended Tuning updates after 4r70w swap?

I am an idiot!!!!!! This is a 1998 4r70w. I had this in my 89 fox body. I built the wiring harness by hand and made sure it was pinned correctly. I am still using the 98 plastic wiring harness in the transmission and didn't change the wiring on the 1995 harness to match..... Good deal.. So after re...
by beyondEOD
Tue Nov 19, 2019 9:07 pm
 
Forum: EEC-V & SN95 Tuning
Topic: Recommended Tuning updates after 4r70w swap?
Replies: 8
Views: 704

Return to advanced search

cron